ISYS
®
WALL MOUNT TOUCHPANELS
Wall Mount Touchpanel Accessories
www.crestron.com | 800.237.2041 | 201.767.3400
© 2007 Specifications subject to change without notice
wall mount touchpanels
INTERFACE MODULES AND CABLES
QM-TX QuickMedia™ Transmitter
The QM-TX provides a low-cost multimedia interface
solution for QuickMedia-based Touchpanels and
MediaManager systems. Portable or rack-mounted,
the QM-TX can be used to send audio, video, and
computer signals to any QM-equipped touchpanel via
Crestron's exclusive single-wire QuickMedia transport.
Five BNC’s are provided on the QM-TX to accept
composite, S-Video, component, HDTV, or RGB
signals (up to 1600 x 1200 at 60 Hz). Balanced stereo
line-level audio signals are transmitted simultaneously
with 24-bit digital resolution. Video formats can be
switched dynamically and automatically under system
control. The QM-TX is 1/2-space rack-mountable
using the optional ST-RMK kit.
SPECIFICATIONS
Video
Gain: 0dB (75 ohm termination)
Bandwidth: 100MHz (-3dB) at unity gain
Formats: Supports standard definition and
HDTV up to 720p and 1080i
RGB
Gain: 0dB (75 ohm termination)
Maximum Resolution: 1600x1200 @ 60Hz (at unity gain)
with cable length of 100 meters and maximum compensation
at receiver (touchpanel)
Audio
A-D Conversion: Burr Brown 24-bit, 48 kHz
Frequency Response: 20Hz to 20kHz
Connectors
R/C/P
R
, G/Y/Y, B/COMP/P
B
, H, V: (5) BNC female
RGB/Video input
Formats: RGBHV, RGBS, RG
S
B, YP
B
P
R
, S-Video (Y/C),
composite;
Input Impedance: 75 ohms (R/C/P
R
, G/Y/Y, & B/COMP/P
B
)
Sync Impedance: 620 ohms (H and V)
Maximum Input Voltage: 0.7 V
P-P
for RGB and C of S-Video;
1 V
P-P
for composite and Y of S-Video; 5 V
P-P
for H and V Sync;
Video signal sensing on Y, COMP, and H
AUDIO: (1) 5-pin 3.5mm detachable terminal block
Balanced/unbalanced stereo line-level audio input
Maximum Input Level: 4 V
RMS
balanced, 2 V
RMS
unbalanced;
Input Impedance: 10k ohms balanced, 5k ohms unbalanced
QM OUT: (1) 8-wire RJ45 female, QuickMedia output port
Connects to QM input port of touchpanel of other
QuickMedia device via CresCAT-QM or CresCAT-IM cable*
NET: (2) 4-pin 3.5mm detachable terminal blocks
Cresnet slave ports, paralleled
Connect to Cresnet control network
G: (1) 6-32 screw, chassis ground lug
LED Indicators
PWR: (green) Indicates DC power supplied from
Cresnet network
NET: (yellow) Indicates communication with Cresnet system
VIDEO ACT: (red) Indicates presence of a valid video
input signal
SETUP (rear): (red) Used for touch-settable ID (TSID)
Controls
SETUP: (1) Button for touch-settable ID (TSID)
Power Requirements
Cresnet Power Usage: 5 Watts (0.21 Amp @ 24 Volts DC)
Environmental
Temperature: 41° to 104°F (5° to 40°C)
Humidity: 10% to 90% RH (non-condensing)
Enclosure
Black metal, 0.5U 19" rack-mountable using optional ST-RMK
(sold separately )
Dimensions
Height: 1.80 in (4.57 cm)
Width: 7.07 in (17.96 cm)
Depth: 7.02 in (17.83 cm)
Weight
2.05 lbs (0.93 kg)
AVAILABLE ACCESSORIES
ST-RMK
Rack Mount Kit
* For QuickMedia wiring use CresCAT-QM or -IM cable; the
maximum aggregate cable length and delay skew between any
QM transmitter (origination point) and QM receiver (endpoint) is
450 ft (137 m) and 22 nS.
111
Comments to this Manuals